Good job Andy. Does your wiper catch on the bonnet at all; think a fairly common Z3 issue? 
The Z3 Bug!
- Thread starter andyglym
- Start date
There's a gap slimmer than a rizzla. Can't say I've noticed to be honest, next time I'm out (whenever that is) I'll put the wipers and check.Good job Andy. Does your wiper catch on the bonnet at all; think a fairly common Z3 issue?
Very good Andy but you're just looking for jobs nowBeen meaning to check the scuttle drains for ages, job done and all is well. Scuttle cleaned and layered with AG bumper gell and seal cleaned and given a layer of Gummifledge.
View attachment 169713
View attachment 169715
Every little helps
. You make me feel guilty for not doing anything to my Zed................nearly
Fourth Road Bridge Dave, don't put off tomorrow what can be done todayVery good Andy but you're just looking for jobs now
Caused by wear in the windscreen wiper spindle, which allows the spindle to move towards the back edge of the bonnet.Good job Andy. Does your wiper catch on the bonnet at all; think a fairly common Z3 issue?
Tony.
Gear Knob changed, out with the old (keeping) and in with the new. Managed not to punch myself in the face when removing, which was nice.
Supersprint Cat Back exhaust.
Winter inner sills check. Not to bad really, should clean up nicely then protected accordingly. Out sills still bearing up well. A good clean and tend to some very minor corrosion. One side at a time.
On leave this week so I'll have time to crack on.
On leave this week so I'll have time to crack on.
- Joined
- Dec 5, 2011
- Points
- 175
The facelift has little stoppers to prevent the wipers catching - subtle improvement
Where do they fit please? Is this a possible upgrade to the early cars?
Victory is mine! 1 x rear quater panel off, that bolt won't be going back in for sure 
Drivers side outer sill, front and rear drivers side panel out, washed and a thick layer of ACF-50 applied to future proof. Primary sills cleaned inside and given a healthy dose of Waxoil and the inner body panels and wheel arches cleaned and given a nice layer of ACF-50. Plastic wheel arch liners cleaned too whilst they're out. Just the surface corrosion on the primary sills to remove, treat then a Liberal dose of Hammerite.
Drivers side outer sill, front and rear drivers side panel out, washed and a thick layer of ACF-50 applied to future proof. Primary sills cleaned inside and given a healthy dose of Waxoil and the inner body panels and wheel arches cleaned and given a nice layer of ACF-50. Plastic wheel arch liners cleaned too whilst they're out. Just the surface corrosion on the primary sills to remove, treat then a Liberal dose of Hammerite.
Bella getting an anti-ageing dermaplane and sill lift? 
Looking good and some solid work. Ez lift is a great item.
Looking good and some solid work. Ez lift is a great item.
Bella "L'Oreal She's Worth It", my favourite childBella getting an anti-ageing dermaplane and sill lift?
I now know why the two extra bolts were holding the wing to the bumper 
First side done and put back together then spotted the gap from the panel to the rear light Wheel arch liner back out and the first of the two bolts in, one to go, the really difficult one, just no space In short, she's had a minor rear end shunt at some point so all is not aligned so the two additional bolts pull the rear wing down to where it should be. Wondered why the shut line from bumper to wing was out of kilter, now I know.
Anyway, tomorrow is another day and that's what leave is for so I'll get to it early doors.
First side done and put back together then spotted the gap from the panel to the rear light
Wheel arch liner back out and the first of the two bolts in, one to go, the really difficult one, just no space In short, she's had a minor rear end shunt at some point so all is not aligned so the two additional bolts pull the rear wing down to where it should be. Wondered why the shut line from bumper to wing was out of kilter, now I know.Anyway, tomorrow is another day and that's what leave is for so I'll get to it early doors.
SimonT
Dedicated Member
That's all looking nice and tight with shiny inners, great job.
Spent a lot of time on the bottom and ends of the sills going back to clean steel where needed, should hopefully last a while now
Looking good Andy ....
- Joined
- Feb 18, 2016
- Points
- 231
- Model of Z
- Z3M Imola and Z4 (e89)
He makes feel as guilty as hellVery good Andy but you're just looking for jobs now
I'm still not washing it though 
SimonT
Dedicated Member
The best stuff I found for cleaning off all of the crud on the panels under the plastic liners was Cif mousse spray. bloody easy cleaning, spray it, agitate it, leave it and wipe it off with a damp sponge. Paint comes up good as new . Cant take any credit though, I read it on here somewhere.
. Cant take any credit though, I read it on here somewhere.
- Joined
- Apr 1, 2016
- Points
- 218
- Location
- Maybole , South Ayrshire
- Model of Z
- Z3 Individual Dakar / Orinoco Individual
Great work going on there Andy .
So many things that are on the to do list
So many things that are on the to do list